informatique:systeme:matos:channel_bonding [Zionetrix]

Cette page est en lecture seule. Vous pouvez afficher le texte source, mais ne pourrez pas le modifier. Contactez votre administrateur si vous pensez qu'il s'agit d'une erreur.
====== Channel Bonding en mode 802.3ad (redondance de lien + équilibrage de charge) ======

On utilise pour ça le mode //802.3ad//.

**Installation de ifenslave : **

  apt-get install ifenslave-2.6

**Fichier /etc/network/interfaces : **
  
  auto bond0
  iface bond0 inet static
      slaves eth0 eth1
      bond-mode 802.3ad
      bond-miimon 100
      bond-downdelay 200
      bond-updelay 200
      address 192.168.0.1
      network 255.255.255.0
      gateway 192.168.0.254

<note important>Il peut être nécessaire de forcer le mode de //bonding// au moment du chargement du module kernel (rencontré avec un switch Cisco notamment et le mode 802.3ad). Dans ce cas, éditer le fichier ///etc/modprobe.d/bonding.conf// et ajouter : <code>options bonding mode=4 miimon=100</code></note>

===== Utilisation avec des VLANs =====

<code>
auto bond0
iface bond0 inet manual
    slaves eth0 eth1
    bond-mode 802.3ad
    bond-miimon 100
    bond-downdelay 200
    bond-updelay 200

auto vlan1
iface vlan1 inet static
    vlan-raw-device bond0    
    address 192.168.0.1
    network 255.255.255.0
    gateway 192.168.0.254
    
auto vlan2
iface vlan2 inet static
    vlan-raw-device bond0    
    address 192.168.1.1
    network 255.255.255.0
</code>
===== Mode de bonding supporté par le kernel Linux =====

^ Nom ^ ID ^ Description ^
| balance-rr | 0 | Round-robin policy: Transmit packets in sequential order from the first available slave through the last. This mode provides load balancing and fault tolerance. |
| active-backup | 1 | Active-backup policy: Only one slave in the bond is active. A different slave becomes active if, and only if, the active slave fails. The bond's MAC address is externally visible on only one port (network adapter) to avoid confusing the switch. This mode provides fault tolerance. The primary option affects the behavior of this mode. |
| balance-xor | 2 | XOR policy: Transmit based on [(source MAC address XOR'd with destination MAC address) modulo slave count]. This selects the same slave for each destination MAC address. This mode provides load balancing and fault tolerance. |
| broadcast | 3 | Broadcast policy: transmits everything on all slave interfaces. This mode provides fault tolerance. |
| 802.3ad | 4 | IEEE 802.3ad Dynamic link aggregation. Creates aggregation groups that share the same speed and duplex settings. Utilizes all slaves in the active aggregator according to the 802.3ad specification. **Pre-requisites : Ethtool support in the base drivers for retrieving the speed and duplex of each slave. The switch must supports IEEE 802.3ad Dynamic link aggregation. Most switches will require some type of configuration	to enable 802.3ad mode.** |
| balance-tlb | 5 | Adaptive transmit load balancing: channel bonding that does not require any special switch support. The outgoing traffic is distributed according to the current load (computed relative to the speed) on each slave. Incoming traffic is received by the current slave. If the receiving slave fails, another slave takes over the MAC address of the failed receiving slave. **Pré-requis : Ethtool support in the base drivers for retrieving the speed of each slave.** |
| balance-alb | 6 | Adaptive load balancing: includes balance-tlb plus receive load balancing (rlb) for IPV4 traffic, and does not require any special switch support. The receive load balancing is achieved by ARP negotiation. The bonding driver intercepts the ARP Replies sent by the local system on their way out and overwrites the source hardware address with the unique hardware address of one of the slaves in the bond such that different peers use different hardware addresses for the server. |


====== Procédures ======

===== État détaillé d'un bond =====

<code bash>ip -d -s -s link ls dev bond0</code>

===== Création manuelle d'un bond =====

<code>
# create the bonding interface with active-backup mode
ip link add name bond0 type bond mode active-backup

# add the under laying interfaces
# the interface, that has been added first, will be active
ip link set master bond0 dev eth1
ip link set master bond0 dev eth0

# enable the bonding interface
ip link set up dev bond0
ip address add 192.168.100.1/24 dev bond0

# check the results: detailed info and statistics of bond0
ip -s -s -d link ls dev bond0

# check the state of ALL under laying interfaces
# with statistics and details 
ip -s -s -d link ls master bond0

# check the kernel logs
journalctl -kn 20
</code>

Source : https://serverfault.com/a/1064428

===== Changer d'interface active =====

  * Lister les interfaces :
    * <code bash>cat /sys/devices/virtual/net/bond0/bonding/slaves</code>
    * ou : <code bash>ip link show master bond0</code>
  * Voir l'interface active : <code bash>cat /sys/devices/virtual/net/bond0/bonding/primary</code>
  * Changer d'interface active : 
    * <code bash>echo eth1 > /sys/devices/virtual/net/bond0/bonding/primary</code>
    * ou : <code bash>ip link set dev bond0 type bond active_slave eth1</code>

===== Supprimer/ajouter une interface slave à un bond =====

  * Sortir ''eth0'' de son bond actuel : ''ip link set nomaster dev eth0''
  * Mettre ''eth0'' dans ''bond0'' : ''ip link set master bond0 dev eth0''